Goldschmidt alternator

Around 1900 it was realized that the existing technology for generating radio waves, the spark-gap transmitter, was inadequate because it generated damped waves. Efforts were made to design a transmitter that would generate sinusoidal continuous waves, because they could be received at a longer range, and also could be modulated to transmit audio (sound) in addition to Morse code. In 1891 Frederick Trouton pointed out that if an AC generator (alternator), which produces alternating current, could be built to run fast enough, with enough magnetic poles on its armature, it would generate alternating current in the radio frequency range. If ${\displaystyle P}$ is the number of pole pairs and ${\displaystyle U}$ is the rotational speed in revolutions per second, the frequency ${\displaystyle f}$ in hertz of the current produced by an alternator is

${\displaystyle f=PU\,}$

A number of researchers beginning with Elihu Thomson and Nikola Tesla had tried building radio alternators, but they had been unable to produce frequencies above 15 kHz due to the engineering problems of building a machine with many poles that would rotate fast enough.^[4] In 1906 Reginald Fessenden and Ernst Alexanderson at General Electric began to solve the problems and build alternators which could produce frequencies in the radio range, above 20 kHz. However the Alexanderson alternator ran at extremely high speeds; to reach 100 kHz with a 300 pole rotor required a rotor speed of 20,000 RPM, which was at the limit of the engineering ability of the time.^[4] It was 1916 before Alexanderson machines achieved the high power needed for transatlantic communication, and they were extremely complex and expensive.

In 1908 Westinghouse engineer Rudolph Goldschmidt devised an intricate method to enable an alternator to generate high frequency without requiring excessive speeds.^[1] His technique was to exploit resonance and the nonlinear saturation characteristic of the iron rotor to use the alternator as a frequency multiplier as well as a generator.^[1][3][5] By attaching tuned circuits called "reflector" circuits to the stator and rotor windings, Goldschmidt found that an alternator could be made to produce output power at a multiple (harmonic) of its fundamental rotational frequency ${\displaystyle PU}$.^[3] The output frequency of the Goldschmidt alternator was

${\displaystyle f=NPU\,}$

where ${\displaystyle N}$ was a small integer, the harmonic number. ${\displaystyle N}$ was limited to 4 in most practical machines, as losses due to leakage flux increased rapidly with increasing ${\displaystyle N}$. Thus a 100 kHz Goldschmidt machine with ${\displaystyle P}$ = 300 poles would require a rotor speed of only ${\displaystyle U}$ = 5000 RPM, one-fourth that of an equivalent Alexanderson machine. 80% efficiency could be achieved, but in order to keep the leakage flux low enough to achieve this the machine required a very narrow clearance of 0.8 mm between the stator and rotor, which could weigh 5 tons and be moving at a peripheral speed of 200 meters per second.^[3][4] Another challenge was that to reduce hysteresis losses in the iron rotor at radio frequencies, it had to be made of very thin foil laminations, .05 mm (.002 in) thick, separated by paper sheets,^[3] so the rotor was more than 1/3 paper. No rotor of this construction had ever been used in a large machine. The limit of output frequency for Goldschmidt alternators, as well as other alternator technologies, was about 200 kHz. The mechanical problems ultimately limited the use of Goldschmidt machines.

The machine was developed and manufactured by the German company Hochfrequenz-Maschinen Aktiengesellschaft für Drahtlose Telegraphie ("Homag") and was mostly used in Europe. The Goldschmidt machine, like the Alexanderson and other alternator transmitters, was used mainly for high power longwave stations that transmitted radiotelegraphy messages, both commercial stations that handled private traffic, and naval stations that kept governments in touch with their colonies and naval fleets. The first Goldschmidt machine in the UK, a 12 kW, 60 kHz transmitter was installed at Stough in 1912.^[1] A 100 kW, 400 pole unit (top of page) was put into operation at Eilvese, Neustadt-am-Ruebenberger, Germany, and the first machine in the USA was a similar 120 kW, 400 pole, 40.5 kHz unit at Tuckerton, New Jersey.^[3] The Eilvese machine was Germany's main communication channel with the world during World War I, and was used by Kaiser Wilhelm II and US President Woodrow Wilson to negotiate the Armistice that ended the war.

The heyday of the big alternator radio transmitters was around 1918. World War I had brought home to nations the strategic importance of radio communication, as without it they could easily be isolated by enemies cutting their submarine telegraph cables. This precipitated a postwar building boom of large transcontinental alternator radio stations. However these expensive behemoths were obsolete even as they were installed. The invention of the triode vacuum tube in 1906 by Lee De Forest, and the feedback oscillator circuit in 1912 by Edwin Armstrong and Alexander Meissner, made possible smaller and cheaper vacuum tube transmitters which by the end of World War 1 could produce as much radio power as the alternators. By 1921 the Marconi Co. had installed 100 kW vacuum tube transmitters for transatlantic message traffic at its stations at Carnarvon, Wales and Glace Bay, Newfoundland. Due to their huge capital costs, legacy alternator transmitters remained in use through the 1930s and were used in World War 2 to communicate with submarines. It is not known when the last Goldschmidt machine was retired.

The Goldschmidt alternator was one of several types of rotating "radio frequency alternator" machines used as radio transmitters during the first two decades of the 20th century.^{[6] [3][7][4]} Alternator transmitters produced a "cleaner" signal with less harmonics than their main competitor, the Poulsen arc transmitter so they were used in the highest power radiotelegraphy stations.^[8] The machines differed in how they solved the fundamental problem of producing sufficiently high frequencies without exceeding the mechanical capabilities of rotating machines:^[9]

• Alexanderson alternator - Invented by Ernst Alexanderson at General Electric in 1911, this machine had a rotor that turned at a high enough speed to produce the radio frequency signal directly.^[4] It was probably the most widely used type. However the high rotational speed required, around 20,000 RPM,^[4] made the mechanical design very complicated, requiring a water-cooled stator and forced oil lubrication. The Alexanderson alternator took 10 years to develop and was very expensive. It was produced by General Electric and used by its subsidiary RCA and the US Navy.
• Bethenod-Latour alternator - Invented by Joseph Bethenod and Marius LaTour at Société Française Radio-électrique, this machine had two or three rotors on the same shaft.^[3] The output current from the first rotor, at the fundamental frequency ${\displaystyle f=PU}$ was applied to the field coils of the second rotor, producing a current at frequency ${\displaystyle 2f}$. The output of the second rotor was applied to the field coils of the third rotor, producing an output at ${\displaystyle 3f}$. The rotor required forced oil lubrication and the case had to be partially evacuated to reduce friction. At St. Assise in Paris, Bethenod machines of 25 kW, 250 kW, 500 kW were in use.^[3]
• Joly-Arco alternator - In this machine, invented by Georg von Arco around 1911, the alternator produced its signal at a lower fundamental frequency, and the frequency was multiplied 2 to 4 times in separate magnetic frequency doublers,^[3] invented by Vallauri^[10] and Maurice Joly^[11] in 1911,^[12] a nonlinear transformer with its iron core magnetized by a DC current in an auxiliary winding, which produced a harmonic of the fundamental frequency.^[4] This device was developed by Telefunken/AEG^[3] and were installed at their transatlantic wireless telegraphy stations at Sayville, Long Island, USA and Buenos Aires, Argentina^[4][13] Some of the largest were two 400 kW alternators installed in 1916 at Nauen Transmitter Station, Nauen, Germany, which generated 6 kHz at 1200 amps with a 7 ton 1.65 m diameter 240 pole rotor rotating at 1500 RPM, which was increased to 24 kHz with two oil-cooled magnetic doublers. Nauen was Germany's main communications channel during the War, and the alternators were used through World War 2 to communicate with submarines.