Thermoresponsive polymers in chromatography

Modification had also been extended past hydrophobic and hydrophilic attachments, charged compounds have also been introduced to TRPs. Kobayashi et al. had previously performed successful modifications to separate bioactive ionic compounds, and continued on that success to improve separation efficiency of bioactive compounds.^[10] Common methods of separating angiotensin peptides had involved reverse-phased high-performance liquid chromatography (RP-HPLC) and cation-exchange chromatography. RP-HPLC requires the use of organic solvents, which is not favored and current trends are moving away from that. Hydrophobic interaction chromatography requires high concentration salt elutions and eluent cleaning to remove the salt. To address the shortcomings of the previous methods, Kobayashi’s group grafted acrylic acid (anionic acrylate under neutral conditions) and tert-butylacrylamide (hydrophobic) monomers onto PNIPAAm, resulting in PNIPAAm-co-AAc-co-tBAAm (IAtB) onto silica beads as a stationary phase medium. The reason for incorporating both ionic and hydrophobic compounds is multifaceted. The ionic compound improves interactivity with the ionic species, but raises the LCST significantly. The hydrophobic addition counteracts against the raise in LCST and lowers it to a more standard value, but also interacts with the hydrophobic surfaces of biological compounds. This resulted in successful and resolved elution of angiotensin peptides. Additionally, they were able to tune the retention factor for the analytes through isocratic temperature gradient elution. Ideal elutions occurred at 35 °C, but decreasing the temperature to 10 °C or raising it to 50 °C caused faster elutions either way. This is a strong indication that electrostatic and hydrophobic interactions can be similarly affected by changes in temperature. The major advantages from applying these success of this study include stationary phase versatility and maintaining bioactivity of the analytes.

Ayano et al. modified PNIPAAm with cationic N,N-dimethylaminopropylacrylamide (DMAPAAm) and hydrophobic BMA and grafted it onto silica beads to form IDB.^[11] They used pH changes to adjust the LCST. The effect of pH on the LCST is as follows, from a plateau value between pH 4.5 and pH 6.0, the LCST decreased up to pH 9 and below pH 4.5. This can be interpreted as requiring slightly basic or moderately acidic conditions, as the 4.5–6.0 pH region holds a maximum value of the LCST, an unfavorable condition. They used these properties to separate several non-steroidal anti-inflammatory drugs (NSAIDs). The analysis of acidic drugs (salicylic acid: BA; SA; MS; and As) was performed below pH 4.5. MS is hydrophobic only its retention time was affected by an increase in temperature on the column without a terminally modified anion-exchanger (IB column). However, with an anion-exchanger present, dissociated acidic drugs were retained longer at temperatures below LCST, and shorter at temperatures above LCST. When the IBD column compared to recently established PNIPAAm columns, electrostatic forces show remarkably higher retention ability of charged compounds than its hydrophilic predecessor. A single stationary phase can accomplish pharmaceutical separations based on hydrophobic interactions, hydrophilic interactions, and electrostatic interactions merely by adjusting the temperature (while adjusting pH to tweak the LCST).

Selective enzyme and antibody separation can be achieved with the use of specific end groups that conjugate with the specific compounds. This results in a formation of a polymer-enzyme conjugate which can be reversibly precipitated and dissolved by changing the temperature. Chen and Hoffman used N-Hydroxysuccinimide (NHS) ester functional end group on NIPAAm to conjugate selectively with β-D-glucosidase.^[12] They found that the conjugated enzyme could be repeatedly precipitated and dissolved in solution and still maintain sufficient enzymatic activity.

In a study that was published in 1998, Hoshino et al. prepared a TRP with a maltose ligand, evaluated it with concanavalin A (Con A), and attempted to separate and purify α-glucosidase, a thermolabile compound.^[13] Since the goal is to selectively isolate a thermolabile enzyme, a TRP with a small LCST value is desired. To fit this condition, the selected TRP was poly(N-acryloylpiperidine)-cysteamine (pAP), which has an LCST of 4 °C. The terminally bound maltose moiety maintains affinity for both analytes, thus the modified TRP, pAPM, met critical conditions of external temperature requirements and affinity for both target analytes. The solubility properties changed from 4 °C (soluble) to 8 °C (insoluble). Several reagents were tested for the recovery of Con A by desorption which had higher binding affinities to Con A than maltose. These reagents were α-D-glucopyranoside, D-mannose, methyl α-D-mannopyranoside, and glucose. α-D-mannopyranoside was the most effective for desorbing Con A from pAPM at virtually 100% after 1 hour. As a control, pAPM was used to bind Con A from a crude extract, which found the pickup of several impurities but still managed to recover 80% of Con A. This exemplifies the need for selective moieties, maltose not residing among them. Finally, the application of pAPM was tested by attempting to separate α-glucosidase from yeast extract under low temperature conditions. In conclusion, the pAPM was found to recover 68% of α-glucosidase activity tested against, maltose being the selected desorption reagent.

Another interesting development for AC was involved with antibody separation using another TRP-ligand combination. Anastase-Ravion et al. attached a dextran derivative to the classic PNIPAAm to result in a poly(NIPAAm)-DD, and used this stationary phase to separate polyclonal antibodies from subcutaneous rabbit serum.^[14] From the study, the dextran derivative of choice was carboxymethyl dextran benzylamide sulfonate/sulfate, and when bound to the TRP was labeled poly(NIPAAm)-CMDBS. The LCST for the poly(NIPAAm)-CMDBS was raised from 32 °C to 33 °C. To test the success of the affinity binding, the antibodies were eluted with glycine buffer (adjusted to pH 2.6 with HCl).

Promising results were obtained in 2003 in a study that merged the newer developments in affinity chromatography with microfluidic devices. Upon the development of microfluidic technology, coupling it with affinity chromatography meant modifying channel surfaces, packing coated beads, or packing with coated porous material, neither of which allow for replenishing the columns.^[15] This produces limitations that prevent the packing material from being changed or the column being regenerated. The approach they took to address those challenges meant incorporating TRP particles as a reversibly immobilized stationary phase. What separates this development from other AC methods is that the beads on which the modified TRP are attached can reversibly adhere to the inner surfaces of the microfluidic channels. The formulation of the smart bead matrix is a little complex, but in general PNIPAAm is modified two times, first with NHS, then with polyethylene glycol-biotin (PEG-b) resulting in PEG-b/pNIPAAm beads. The inner surface of the microfluidic channels is composed of polyethylene terephthalate, to which the PEG-b/pNIPAAm beads reversibly bind above the LCST. When the sample solution is passed through the channels, the target analyte binds to the biotin ligand. The temperature can then be brought below the LCST to dissociate and become removed from the inner channels. This allows for a system adept to being reloaded with stationary phase under mild conditions. They successfully separated and eluted Streptavidin. Further application of these procedures allow for portable AC columns which can be packed on site and used for local or clinical analytical separations of complex biological fluids.