Tunnel boring machine

1800s

The first successful tunnelling shield was developed by Sir Marc Isambard Brunel to excavate the Thames Tunnel in 1825. However, this was only the invention of the shield concept and did not involve the construction of a complete tunnel boring machine, the digging still having to be accomplished by the then standard excavation methods.^[8]

The first boring machine reported to have been built was Henri Maus' Mountain Slicer.^{[9][10][page needed][11][12]} Commissioned by the King of Sardinia in 1845 to dig the Fréjus Rail Tunnel between France and Italy through the Alps, Maus had it built in 1846 in an arms factory near Turin, Italy. It consisted of more than 100 percussion drills mounted in the front of a locomotive-sized machine, mechanically power-driven from the entrance of the tunnel. The Revolutions of 1848 affected the funding, and the tunnel was not completed until 10 years later, by using less innovative and less expensive methods such as pneumatic drills.^[13]

In the United States, the first boring machine to have been built was used in 1853 during the construction of the Hoosac Tunnel in northwest Massachusetts.^[14] Made of cast iron, it was known as Wilson's Patented Stone-Cutting Machine, after inventor Charles Wilson.^[15] It drilled 3 meters (10 ft) into the rock before breaking down (the tunnel was eventually completed more than 20 years later, and as with the Fréjus Rail Tunnel, by using less ambitious methods).^[16] Wilson's machine anticipated modern TBMs in the sense that it employed cutting discs, like those of a disc harrow, which were attached to the rotating head of the machine.^[17][18][19] In contrast to traditional chiseling or drilling and blasting, this innovative method of removing rock relied on simple metal wheels to apply a transient high pressure that fractured the rock.^{[citation needed]}

In 1853, the American Ebenezer Talbot also patented a TBM that employed Wilson's cutting discs, although they were mounted on rotating arms, which in turn were mounted on a rotating plate.^[20] In the 1870s, John D. Brunton of England built a machine employing cutting discs that were mounted eccentrically on rotating plates, which in turn were mounted eccentrically on a rotating plate, so that the cutting discs would travel over almost all of the rock face that was to be removed.^[21][22]

The first TBM that tunneled a substantial distance was invented in 1863 and improved in 1875 by British Army officer Major Frederick Edward Blackett Beaumont (1833–1895); Beaumont's machine was further improved in 1880 by British Army officer Major Thomas English (1843–1935).^{[23][24][25][26][27]} In 1875, the French National Assembly approved the construction of a tunnel under the English Channel and the British Parliament supported a trial run using English's TBM. Its cutter head consisted of a conical drill bit behind which were a pair of opposing arms on which were mounted cutting discs. From June 1882 to March 1883, the machine tunneled, through chalk, a total of 1,840 m (6,036 ft).^[12] A French engineer, Alexandre Lavalley, who was also a Suez Canal contractor, used a similar machine to drill 1,669 m (5,476 ft) from Sangatte on the French side.^[28] However, despite this success, the cross-Channel tunnel project was abandoned in 1883 after the British military raised fears that the tunnel might be used as an invasion route.^[12][29] Nevertheless, in 1883, this TBM was used to bore a railway ventilation tunnel – 2 m (7 ft) in diameter and 2.06 km (6,750 ft) long – between Birkenhead and Liverpool, England, through sandstone under the Mersey River.^[30]

Construction of the Uptown Hudson Tubes for the Hudson & Manhattan Railroad took place intermittently between 1890 and 1908, using a Greathead Shield. The project used air compressed to 2.4 bar (35 psi) to reduce cave-ins. However, there were many workers that died via cave-in or decompression sickness.^[31][32][7]

1900s

During the late 19th and early 20th century, inventors continued to design, build, and test TBMs for tunnels for railroads, subways, sewers, water supplies, etc. TBMs employing rotating arrays of drills or hammers were patented.^[33] TBMs that resembled giant hole saws were proposed.^[34] Other TBMs consisted of a rotating drum with metal tines on its outer surface,^[35] or a rotating circular plate covered with teeth,^[36] or revolving belts covered with metal teeth.^[37] However, these TBMs proved expensive, cumbersome, and unable to excavate hard rock; interest in TBMs therefore declined. Nevertheless, TBM development continued in potash and coal mines, where the rock was softer.^[38]

A TBM with a bore diameter of 14.4 m (47 ft 3 in) was manufactured by The Robbins Company for Canada's Niagara Tunnel Project. The machine was used to bore a hydroelectric tunnel beneath Niagara Falls. The machine was named "Big Becky" in reference to the Sir Adam Beck hydroelectric dams to which it tunneled to provide an additional hydroelectric tunnel.

2000s

The TBM known as Bertha, reportedly the largest earth pressure balance machine and second largest TBM in general (as of June 2023), has a bore diameter of 17.45 meters (57.3 ft), and was produced by Hitachi Zosen Corporation in 2013.^{[2][39][better source needed]} It was delivered to Seattle, Washington, for its Highway 99 tunnel project.^{[40][full citation needed]} The machine began operating in July 2013, but stalled in December 2013 and required substantial repairs that halted the machine until January 2016.^[41] Bertha completed boring the tunnel on April 4, 2017.^{[42][full citation needed]}

Two TBMs supplied after the 2013 acquisition of Germany's Aker Wirth (Aker Solutions) TBM and shaft-boring technology by China Railway Tunnelling Equipment (CRTE), now CREG (China Railway Engineering Equipment Group)-Germany,^{[43][44][better source needed]} CREG-Wirth units with boring diameter of 6.67 m (21.9 ft), were used to bore two tunnels for Kuala Lumpur, Malaysia's Metro system.^{[44][better source needed]} The medium excavated was water "saturated sandy mudstone, schistose mudstone, highly weathered mudstone as well as alluvium".^{[44][better source needed]} By the company's commercial description, its products achieved an advance rate of "more than 345 meters [1,130 feet] per month".^{[44][better source needed]}

Reportedly the largest hard rock machine and fourth largest TBM overall (as of June 2023), a machine known as Martina, was built by Herrenknecht AG.^[2] Its excavation diameter is 15.62 m (51.2 ft), and total length 130 m (430 ft); excavation area of 192 m² (2,070 sq ft), and thrust value 39,485 t,^{[clarification needed]} total weight 4,500 tons, and total installed capacity 18 MW.^[2] Its yearly energy consumption was about 62 GWh.^[2] Martina was used by the Italian Toto Group construction company (Toto S.p.A Costruczioni General) to bore a 2.4 km tunnel of the Variante di Valico project near Florence, Italy, in 2013. This project created the Sparvo gallery of the Italian Motorway Pass A1 ("Variante di Valico A1"), near Florence.^{[citation needed]} As of this date,^[when?] Martina was still owned and operated by the Toto Group.^{[citation needed]}

Herrenknecht also built the world's largest-diameter slurry TBM and as of June 2023, per Guinness World Records, also the largest TBM overall; called the "Qin Liangyu" or Mixshield S-880, it has an excavation diameter of 17.63 meters (57.8 ft).^[2] Owned and operated by a subsidiary of the French construction company Bouygues (Dragages Hong Kong), it was used to bore the Chek Lap Kok to Tuen Mun road tunnel, undersea, to Hong Kong, China, clearing the first section of the tunnel at the large diameter, then being converted to 14 m, and working alongside three other TBMs (including another Herrenknecht borer) to complete the tunnels, 30 m undersea, in 2019.^[2] A robbins TBM in 2022 underwent an in-tunnel diameter change, that reduced the diameter of the TBM from 11.6 meters to 9.9 meters.^[45]

In 2026, China Railway Science & Industry Group (CRSIC) and Tsinghua University introduced Lucky Dragon, a 4.5 m (15 ft) diameter hard rock TBM that included a hybrid boring/blasting cutter head. It combined a standard cutterhead with a drilling system that used explosives to fracture to speed the boring process.^[46]

Open/gripper

Gripper TBMs are used in rock tunnels. They push directly against the unreinforced sides of the tunnel.^[7]

Machines such as a Wirth machine move only while the grips are released, while other machines move continuously. At the end of a Wirth boring cycle, legs drop to the ground, the grippers are retracted, and the machine advances. The grippers then reengage and the rear legs lift for the next cycle. Such TBMs can be steered by adjusting the relative length of the grippers.^[47]

Open face soft ground

Open face soft ground TBMs rely on the excavated ground to briefly stand without support. They are suitable for use in ground with strength of up to about 10 MPa (1,500 psi) with low water inflows. They can bore tunnels with cross-section in excess of 10 m (30 ft). A backactor arm or cutter head bore to within 150 mm (6 in) of the edge of the shield. Some TBMs allow the cutter head to be retracted for maintenance or to allow inspection of the cutting face.^{[citation needed]}

Earth pressure balance

An earth pressure balance (EPB) machine is used in soft soil with less than 7 bar (100 psi) of pressure. It uses muck to maintain pressure at the tunnel face. The muck (or spoil) enters the TBM via a screw conveyor. By adjusting the rate of muck extraction and the advance rate, the pressure at the face can be controlled. Additives such as bentonite, polymers, or foam can be injected ahead of the face to stabilize the ground. Such additives can be injected through the cutter head or extraction screw to ensure that the muck is sufficiently cohesive to maintain pressure and restrict water flow.

The cutter head uses a combination of tungsten carbide cutting bits, carbide disc cutters, drag picks and/or hard rock disc cutters.

EPB has enabled tunneling through soft, wet, or unstable ground with greater speed and safety. The Channel Tunnel, the Thames Water Ring Main, sections of the London Underground, and most new metro tunnels completed in the last 20 years worldwide used an EPB machine.^[52]

Slurry shield

Slurry shield machines can be used in soft ground with significant water pressure and are favored where granular ground conditions (sands and gravels) do not allow a plug to form in the screw. Pressurised slurry typically made of bentonite clay is injected through the cutter head. The slurry applies hydrostatic pressure to the face, mixing with the muck before it is extracted. The mixture is pumped to a slurry separation plant, typically outside the tunnel.

Mixshield machines are aimed at mixed-face conditions (mixed soft soil and rock/boulders). These include hybrid cutter head tooling, enhanced rock crushing, and refined pressure-regulation systems (possibly employing air-cushions) that maintain stable face pressure as ground types vary. The slurry circuit and bulkhead offer greater tolerance of coarse material and sudden changes in ground consistency.^[53]

Slurry separation plants use multi-stage filtration systems that separate spoil from slurry to allow slurry reuse. The degree to which slurry can be 'cleaned' depends on the relative particle sizes of the muck. Slurry TBMs are not suitable for silts and clays as the muck particle size is smaller than that of the bentonite. In this case, water is removed from the slurry leaving a clay "cake", which may be polluted.

A caisson system may be placed at the cutter head to allow workers to work on it, for example replacing worn cutter blades.^[54][55] Above-ambient air pressure may occur in the caisson, requiring workers to be medically cleared as "fit to dive" and trained to operate pressure locks.^[54][55] Workers pass through an airlock to reach the cutting head.^[56][57][58] Some systems allow this to be done robotically.^[59]

Slurry TBMs may incorporate jaw crushers, to crush boulders that the TBM encounters. This is necessary so that the pieces can be extracted with the slurry. A screen prevents fragments that are too large from entering the slurry, avoiding clogs in slurry lines.^[49]

Variable density

VDTBMs are a combination of EPB and Slurry types. They can switch between EPB, slurry, high-density slurry, and open modes, supporting tunneling in heterogeneous ground conditions without requiring mechanical modification other than the addition/removal of a slurryfier box. Multi-mode TBMs are a related type that can switch between open and EPB or open and slurry modes and are a precursor to VDTBMs.^[60][61]

Tunnel size

TBMs range diameter from 1 to 23 meters (3 to 75 ft).^[62] Micro tunnel shield TBMs are used to construct small tunnels, and is a smaller equivalent to a general tunnelling shield and generally bore tunnels of 1 to 1.5 meters (3.3 to 4.9 ft), too small for operators to walk in.

Concrete lining

Shielded TBMs are typically used to excavate tunnels in soil. They erect concrete rings behind the TBM to support the tunnel walls.^{[63] [page needed]} New rings are added as the TBM advances. Each ring is made of several separate segments. The final segment, the key, (often wedge shaped) pushes/locks the other segments together to stabilize the ring.^[64][65] The segments can be bolted to each other to further increase stability. Neoprene rubber seals and/or grouting can reduce water ingress.^[66]

Pipe lining

Pipe jacking TBMs are often used for small diameter tunnels, up to 2 meters in width. To advance the TBM, new sections of pipe are inserted into the tunnel shaft and advanced by a hydraulic jack, which advances the TBM, which is attached to the other end of the pipe. The TBM cannot be steered until it arrives at another shaft. Bentonite can be injected into the space between the pipe and the ground as a lubricant to extend the distance between shafts. Additional jacks can be placed in between pipe segments to extend this distance.^[67] Large rectangular tunnels have been excavated using this method.^[68][69]

Single shield

A single-shield TBM has a single cylindrical shield after the cutter head. A permanent concrete lining is constructed immediately after the shield, and the TBM pushes off the lining to apply force to the cutter head. Because this pushing cannot be done while a next ring of lining is being constructed, the single-shield TBM operates in alternating cutting and lining modes. Articulation hydraulic cylinders can be used to steer the TBM.^[70]